1. Briggs And Stratton Model 650 Series 190cc Engine Manual

Find Your Snapper Manual & Parts Lists. They are used to look up your product's Operator's Manual and Illustrated Parts Lists. Briggs & Stratton. Briggs & Stratton Genuine Parts Our genuine parts are specially designed to exact OEM standards, manufactured and tested to help deliver optimum performance in Briggs & Stratton engines. Due to an upgrade of core backend systems, we're unable to process parts orders during the next several weeks.

. Operator’s Manual Model 120000 Quantum 600 Series 625 Series 650 Series 675 Series Quick Start Guide on page 4 ECopyright Briggs & Stratton Corporation Form No.

277039-9/06 BRIGGSandSTRATTON.com Milwaukee, Wisconsin 53201 U.S.A. Printed in U.S.A. Safety References The safety alert symbol is used to identify safety information about hazards that can result in personal injury.

A signal word (DANGER, WARNING, or CAUTION) is used with the alert symbol to indicate the likelihood and the potential severity of injury. In addition, a hazard symbol may be used to represent the type of hazard.

Know Your Engine Fuel fill Choke (if equipped) Primer Spark plug Side oil drain plug (if equipped) Rewind/Starter handle Front view Air cleaner Back view Oil cap & Oil dipstick Muffler Speed control lever. This manual contains safety information to make you aware of the hazards and risks associated with engines. Read the Operating Manual before starting your engine. ADD OIL WHAT KIND?

High quality SAE 30 motor oil. To FULL line on dipstick. Engine holds about 20 oz.

ReadyStart ™ go to step 4. PUSH PRIMER HOW MANY TIMES? Press times the FIRST TIME you start engine. For all future starts, press times. Locate primer bulb. Press with finger. Wait two seconds between each press.

SPECIAL CONCERNS? Pressing primer too many times can flood engine with gas.

Briggs And Stratton Model 650 Series 190cc Engine Manual

Troubleshooting Starter Handle will not pull. R The bail, operator control bar, is not engaged which releases the brake from the flywheel allowing the engine to turn over. R Place equipment on flat level surface.

Ensure all external equipment/engine loads are removed before starting engine. ReadyStart E Instructions Check oil level. Ensure level is at FULL mark on dipstick. Use a high quality motor oil. Check the oil recommendations for the correct oil type for expected starting temperature.

Move speed control to FAST, if equipped. Operate engine in FAST position. Starting Instructions Check oil level. Ensure level is at FULL mark on dipstick. Use a high quality motor oil. Check the oil recommendations for the correct oil type for expected starting temperature. Open fuel shut-off valve1/4 turn, if equipped.

Firmly push primer bulb 3 times, if equipped. Move speed control to FAST, if equipped. Operating Engine After engine has started, let it warm up several seconds to several minutes, depending on outside temperature. For maximum performance and life, operate engine with speed control in FAST, if equipped. Do not tip engine or equipment at angle which causes gasoline to spill.

Capacity The engine holds approximately (18 oz.; 0.5 liter). Use a high quality SAE 30 weight motor oil. Do not use special additives.

Choose a viscosity according to the table opposite. Note: Synthetic oil meeting ILSAC GF-2, API certification mark and API service symbol (shown at left) with “SJ/CF ENERGY CONSERVING”. Changing Oil Change oil after first 5 to 8 hours of use, then every 50 hours or every season. Change oil every 25 hours when operating the engine under heavy load or in high temperatures.

Run engine until it runs out of fuel. Otherwise, fuel can leak out, creating a fire/explosion hazard, when you tip engine in Step 4. Adding Fuel Remove cap.

Fill tank to approximately one inch below top of neck to allow for fuel expansion. Be careful not to overfill. Replace cap before starting.

Fuel Fill Fresh StartE Fuel Cap Your engine may be equipped with a Fresh Start fuel cap. Engine Specifications This is a single cylinder, L-head, air-cooled engine.

It is a low emissions engine. In the state of California, model 120000 engine covered in this manual is certified by the California Air Resources Board to meet emissions standards for 125 hours. Engine Maintenance Regular maintenance will improve the performance and extend the life of the engine.

See any Authorized Briggs & Stratton Dealer for service. Use only genuine Briggs & Stratton parts. Other parts may not perform as well, may damage the engine, and may result in injury.

Air Cleaner All engines have an air cleaner cartridge. The cartridge is either flat or oval (see illustrations). In addition, some engines have a pre-cleaner. Pre-cleaner To clean pre-cleaner (if equipped), separate it from cartridge and wash in liquid detergent and water. Air dry thoroughly. Combustion Deposits We recommend that after every 100-300 hours you have an authorized Briggs & Stratton Service Dealer remove combustion deposits from the cylinder, cylinder head, top of piston, and around valves. Muffler Replacement parts for the muffler must be the same and installed in the same position as the original parts, otherwise fire can occur.

Storage Engines stored over 30 days need special attention. To prevent gum from forming in fuel system or on essential carburetor parts: a) if fuel tank contains oxygenated or reformulated gasoline (gasoline blended with an alcohol or an ether), run engine until it stops from lack of fuel, or b) if fuel tank contains gasoline, either run engine until it stops from lack of fuel, or add a gasoline additive to the gas in the tank. Warranty Information Briggs & Stratton Corporation (B&S), the California Air Resources Board (CARB) and the United States Environmental Protection Agency (U.S. EPA) Emissions Control System Warranty Statement (Owner’s Defect Warranty Rights and Obligations) The California Air Resources Board (CARB), U.S. EPA and B&S are pleased to explain the Emissions Control System Warranty on your small off-road engine (SORE). BRIGGS & STRATTON ENGINE OWNER WARRANTY POLICY Briggs & Stratton Corporation will repair or replace, free of charge, any part(s) of the engine that is defective in material or workmanship or both. Transportation charges on parts submitted for repair or replacement under this warranty must be borne by purchaser.

ABOUT YOUR ENGINE WARRANTY Briggs & Stratton welcomes warranty repair and apologizes to you for being inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate.

For example, warranty would not apply if engine damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper installation.

Select your Engine Model Series Below: Model Number Example Where do I find the model number? Basic Engine Repair Advanced Engine Repair Engine Theory Video Briggs & Stratton Engine Model Numbers 000 000 000 000 000 000 09C900 09T900 121K00 100 100 122400 122L00 122Q00 122R00 100 100 100 100 100 126K00 1 128L00 128T00 12A100 12A300 12D100 12D200 1 12H100 12H300 12L300 12L900 12M900 12Q500 12Q600 12Q900 12R900 100 100 15T000 100 200 200 200 200 200 200 200 243700 28F700 31E500 354400 49G500 49M700 49M800.